GaleAir / Guides
How to measure your furnace filter (nominal vs. actual)
The three numbers on a filter frame — 16x25x1, for example — are a rounded name, not the exact size of the cardboard. That is why a “same size” replacement can look smaller, or refuse to slide in.
Nominal size is the name you order by
Nordic Pure describes nominal size as the rounded, labeled measurement used for shopping, and actual size as the true dimensions, typically a fraction smaller. They put it plainly: think of the nominal size as the “name” of the filter, not the exact size.
On their measuring page, Nordic Pure says actual size is usually 0.25–0.5 inch smaller than the label, and gives an example: a filter labeled 16x25x1 may actually measure 15.5 × 24.5 × 0.75 inches. On a related page they give a different example for 16x20x1: 15.75 × 19.75 × 0.75 inches. Those are examples, not a universal formula. The exact undercut depends on the brand.
Actual size is not the same from brand to brand
Filterbuy, a filter manufacturer, says the same thing in stronger terms: nominal sizes are shared across the industry, but actual sizes aren’t, so a new brand can bind or leave a gap even when the label matches your old one.
Filterbuy states that it cuts length and width 0.5 inch under nominal on purpose, so the filter can slide in without binding, and it publishes actual sizes for its own products. Examples from its fit guide:
| Nominal (order this) | Filterbuy’s published actual size |
|---|---|
| 16x25x1 | 15.5 × 24.5 × 0.75 in |
| 20x25x1 | 19.5 × 24.5 × 0.75 in |
| 20x20x1 | 19.5 × 19.5 × 0.75 in |
| 16x20x1 | 15.5 × 19.5 × 0.75 in |
| 16x25x4 | 15.5 × 24.5 × 3.63 in |
| 20x25x4 | 19.5 × 24.5 × 3.63 in |
| 20x25x5 | 19.5 × 24.5 × 4.75 in |
The same Filterbuy page compares a 20x25x1 across brands (figures Filterbuy published, not independent laboratory measurements by GaleAir): Filterbuy 19.50 × 24.50 × 0.75; Filtrete (3M) 19.68 × 24.68 × 0.81; Amazon Basics 19.75 × 24.75 × 0.75. For 20x25x4, Filterbuy lists its own filter at 19.50 × 24.50 × 3.63 and Filtrete at 19.88 × 24.63 × 4.31. That depth difference is large enough to matter in a tight cabinet.
Use the size finder to look up those published figures. If a size isn’t in the source tables, we will not invent one.
How to measure, step by step
The U.S. EPA’s consumer guide says to make sure the filter fits snugly so air does not leak around it, and so you do not have to bend or crush the filter to make it fit. The steps below combine that test with manufacturer measuring advice.
- Turn the system off at the thermostat before you open a filter slot or cabinet. Filterbuy includes this as the first step; it is also common safety practice around moving blowers.
- Look at the current filter’s frame. If the nominal size is still printed clearly, write it down. That is usually what you should order again, as long as the old filter actually fit.
- Note the airflow arrow before you pull the filter out. The DOE’s Building America Solution Center (Pacific Northwest National Laboratory) says to install the new filter with the arrow pointed in the direction of airflow, toward the furnace or air handler in a return slot or grille.
- Prefer measuring the empty slot, not only the old filter. Filterbuy warns that a filter that has spent a season in the airflow is often bowed, so it reads short.
- Measure length, width, and depth of the opening (or of the filter, if you are checking a new one). Write all three numbers in inches.
- Translate those measurements into a nominal size. Filterbuy’s fit guide says: if you measured the slot, round each number to the nearest whole inch and write short × long × depth, such as 16x25x1. Nordic Pure, describing how to measure an old filter, says to round up to the nearest inch for the nominal size. Those two rounding rules can disagree on a borderline measurement — which is another reason to trust the slot, the printed label if the old filter fit well, and the actual size on the new package.
Watch the depth as carefully as the face size
Filterbuy notes that depth is ordered wrong more often than any other dimension. A 4-inch and a 5-inch cabinet are not interchangeable. In Filterbuy’s own lineup, a “4-inch” filter is 3.63 inches deep and a “5-inch” is 4.75 inches deep; they point out that the 5-inch will not fit a 4-inch slot, and the 4-inch will not fill a 5-inch cabinet the same way.
What if the new filter looks smaller?
First, read the actual size printed on both frames. If both are the same nominal size but different actuals, that is expected when you switch brands. If the gap looks larger than about 3/8 inch, don’t assume it is “close enough” — unfiltered air can go around the media. If the new filter has to be forced or bowed, it is too big, turned the wrong way, or too deep. GaleAir can’t inspect your cabinet from here; when the fit is unclear, measure again or ask an HVAC technician.
Shop by size — affiliate link placeholder (not active yet)
Sources
Opened and used while writing this page:
- Nordic Pure, “How to Measure,” https://www.nordicpure.com/how-to-measure/
- Nordic Pure, “Nominal Size vs. Actual Size: A Guide to Measuring AC & Furnace Air Filters Correctly,” https://www.nordicpure.com/nominal-size-vs-actual-size-a-guide-to-measuring-ac-furnace-air-filters-correctly/
- Filterbuy, “How to Check If Your Filter Fits Properly (and Why It Matters),” https://filterbuy.com/resources/how-to-guides-and-hvac-maintenance/air-filter-fit-guide/
- U.S. EPA, “Guide to Air Cleaners in the Home” (last updated October 1, 2026), https://www.epa.gov/indoor-air-quality-iaq/guide-air-cleaners-home
- U.S. DOE Building America Solution Center (PNNL), “Proper Installation of Furnace and Air-Handler Filters,” https://basc.pnnl.gov/resource-guides/proper-installation-furnace-and-air-handler-filters